rev. jun 04, 2004 page 1 of 3 hpt triple output dc-dc converters provide 15 watts of output power in an industry standard package. hpt?s feature excellent efficiency and industry-leading power density. the hpt has open-frame packaging to provide maximum useable power with minimal thermal constraints. these units are fully compatible with production board washing processes. ? triple-output 2? x 2? ? open-frame packaging ? 2.5 million hours mtbf ? short-circuit and overvoltage protection ? 500v isolation ? input undervoltage lockout ? 3-1 wide voltage input ? 100c baseplate operation description features technical specifications voltage range 24 vdc nominal 10 - 30 vdc 48 vdc nominal 34 - 75 vdc 48 vdc wide 20 - 60 vdc input notes 1 for negative logic, add suffix ?n? to model number. ? mtbf predictions may vary slightly from model to model. specifications typically at 25c, normal line, and full load, unless otherwise stated. soldering conditions: i/o pins, 260c, ten seconds; fully compatible with commercial wave-soldering equipment. safety: agency approvals may vary from model to model. please consult factory for specific model information. units are water-washable and fully compatible with commercial spray or immersion post wave-solder washing equipment. output setpoint accuracy 1% auxiliary setpoint accuracy 5% line regulation v in min. - v in max., i out rated 1% v out load regulation i out min. - i out max., v in nom. 1% v out minimum output current 10 % i out rated dynamic regulation, loadstep 25% i out pk deviation 1% v out settling time 250 s ripple and noise w/ 25 mhz bw, pk-pk / rms 1% / 0.3% v out current limit type hiccup current limit threshold range, % of i out rated 110 - 140% short circuit current max. 200% i out nom. ovp trip range 110 - 140% v out nom. ovp type second control loop switching frequency 200 khz isolation input - output 500 vdc input - case 500 vdc output - case 500 vdc temperature coefficient 0.02 ppm/c case temperature operating range -40 to +100c storage range -40 to +125c thermal shutdown range 105 to 115c humidity max., non-condensing 95% vibration, 3 axes, 5 min each 2 g mtbf ? (bellcore tr-nwt-000332) 2.5 x 10 6 hrs safety consult factory weight (approx.) 0.85 oz general hpt dc-dc series data sheet triple-output, 15 watts
model input voltage input voltage maximum input output rated output ripple & noise typical (volts) range (volts) current (amps)* voltage (volts) current (amps) pk-pk (mv) efficiency** hpt015yehh-a 24 18-36 1.90 3.3, 12 2.3, 0.31 100, 200 80% hpt015yejj-a 24 18-36 1.90 3.3, 15 2.3, 0.25 100, 200 80% hpt015yghh-a 24 18-36 1.84 5, 12 1.5, 0.31 100, 200 83% hpt015ygjj-a 24 18-36 1.84 5, 15 1.5, 0.25 100, 200 83% hpt015zehh-as1 48 34-75 0.56 3.3, 12 2.3, 0.31 100, 200 80% hpt015zejj-as1 48 34-75 0.56 3.3, 15 2.3, 0.25 100, 200 80% hpt015zghh-as1 48 34-75 0.54 5, 12 1.5, 0.31 100, 200 83% hpt015zgjj-as1 48 34-75 0.54 5, 15 1.5, 0.25 100, 200 83% hpt015zehh-a 48 wide 20-60 0.95 3.3, 12 2.3, 0.31 100, 200 80% hpt015zejj-a 48 wide 20-60 0.95 3.3, 15 2.3, 0.25 100, 200 80% hpt015zghh-a 48 wide 20-60 0.92 5, 12 1.5, 0.31 100, 200 83% hpt015zgjj-a 48 wide 20-60 0.92 5, 15 1.5, 0.25 100, 200 83% notes: * maximum input current at minimum input voltage, maximum rated output power. ** at nominal v in , rated output. rev. jun 04, 2004 triple-output, 15 watts page 2 of 3 hpt dc-dc series data sheet natural convection 11.2 c/w 100 lfm 9.6 c/w 200 lfm 6.8 c/w 300 lfm 5.1 c/w 400 lfm 4.2 c/w tolerances mechanical drawing inches: (millimeters) .xx 0.020 .x 0.5 .xxx 0.010 .xx 0.25 pin: 0.002 0.05 (dimensions as listed unless otherwise specified.) thermal impedance note: thermal impedance data is dependent on many environmental factors. the exact thermal performance should be validated for specific application. pin function 1+v in 2-v in 3+v out 4+v out 5-v out 6-v out
model selection model numbers highlighted in yellow or shaded are not recommended for new designs.
rev. jun 04, 2004 options page 3 of 3 this page is offered as a reference. consult factory for actual availability of options. when ordering equipment options, use the following suffix information. select preferred option(s) and add the suffix to the model number. ordering option examples are located below the options table. nuclear and medical applications - power-one products are not authorized for use as critical components in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written consent of the respective divi sional president of power-one, inc. technical revisions - the appearance of products, including safety agency certifications pictured on labels, may change dependin g on the date manufactured. specifications are subject to change without notice. option suffix applicable series remarks negative logic n has, hbd, hbs, hes, hls, hld, les, ttl "low" turns module on qbs, qes, qls, tes, tqd ttl "high" turns module off lucent-compatible trim t has, hbd, hbs, hes, hls, qbs, qes, qls trim 1 ias, les enable 2 iad, ias, les, sms trim and enable 3 ias, les pin length and heat sink options standard pin length is 0.180" (4.6mm) 0.110" (2.8mm) pin length 8 all leaded models 0.150" (3.8mm) pin length 9 all leaded models 0.24" (6.1mm) horizontal heat sink 1h all 1/4-bricks, 1/2-bricks, 3/4-bricks, full-bricks includes thermal pad (except hls, hld, qls, tld, and tkd packages) 0.24" (6.1mm) vertical heat sink 1v all 1/4-bricks, 1/2-bricks, 3/4-bricks, full-bricks includes thermal pad (except hls, hld, qls, tld, and tkd packages) 0.45" (11.4mm) horizontal heat sink 2h all 1/4-bricks, 1/2-bricks, 3/4-bricks, full-bricks includes thermal pad (except hls, hld, qls, tld, and tkd packages) 0.45" (11.4mm) vertical heat sink 2v all 1/4-bricks, 1/2-bricks, 3/4-bricks, full-bricks includes thermal pad (except hls, hld, qls, tld, and tkd packages) 0.95" (24.1mm) horizontal heat sink 3h all 1/4-bricks, 1/2-bricks, 3/4-bricks, full-bricks includes thermal pad (except hls, hld, qls, tld, and tkd packages) 0.95" (24.1mm) vertical heat sink 3v all 1/4-bricks, 1/2-bricks, 3/4-bricks, full-bricks includes thermal pad (except hls, hld, qls, tld, and tkd packages) example options: hbs050zg-ant3v = hbs050zg-a with negative logic, lucent-compatible trim, and 0.95? vertical heat sink. les015yj-3n = les015yj with optional trim and enable, negative logic. qbs066zg-at8 = qbs066zg-a with lucent-compatible trim and 0.110? pin length.
|
